Flowjet Valves : Industrial Valves Manufacutrer

Forge Steel Gate Valve

Flowjet have a wide range of GATE VALVES in variety of types, sizes, pressure ratings and materials, with wafer type, screwed, welded or flanged connections. Flowjet Manufacture Gate valves in every size ranging from the smallest to the largest size Gate Valve name is derived from the operation of the Gate valve.

The Valve Acts like a Gate to stop or allow the flow through the valve. The valve can be opened by lifting the wedge out of the path of the flow Gate valves are actually designed for closing & opening full , so they are not suitable for the Throttling purpose. When the Gate valve is fully open, there is no Obstruction in the Flow path, resulting in very low pressure drop, & they are often suitable for the Hot Tapping & Pigging.

Gate Valves are actually designed for use with the flow of liquids and Gases but there are variation to cope with the specific requirements.

For example, one problem with wedge gate valves in steam service is that when the valve is closed and steam is brought into the system, the metal wedge expands and can get stuck, making opening the valve difficult or impossible.

Knife-gate valves are used when deposit may block a normal wedge gate. The gate is a narrow plate with a shaped edge to cut through solids. They are ideal for applications with a high suspension of solids or fibrous content such as powders, slurry, ash and pulp. Care should be taken when specifying knife gate valves to state whether flow is uni- or bi-directional.

SIZE RATING

Rating: 800#
Size: 15 TO 50MM Or 1/2 TO 2Inches
Rating: 1500#
Size: 15 TO 50MM Or 1/2 TO 2Inches
Rating: 2500#
Size: 15 TO 50MM Or 1/2 TO 2Inches
SIZE AND RATINGS
VARIANTS
  • Metal Seated Wedge Gate Valves
  • Resilient Seated Wedge Gate Valves
  • Cap top, hand wheel, gearbox or actuated option
MANUFACTURING STANDARDS 
MFG DESIGNASME B16.34 / API 602/ISO15761
FACE TO FACE DIMENSION As PerMFG
END CONNECTIONSsrewed End/soket Weld End/ Butt Weld end
KEY FEATURES
  • Anti-frictional Ball bearings in higher sizes and classes.
  • The strength of Stem to Gate connection is stronger than the strength of the Stem at the root of the operating thread
  • Outside screw and yoke construction
  • Valves with backseat arrangement
  • Bi-directional shut-off
  • Gland is of self aligning
  • Deep stuffing box
  • Low Pressure Drop & Lower Erosion
  • The Body to Bonnet is male and female joint and ring joint is used in higher classes
MATERIAL
S.NO.PART NAMEMATERIAL OPTION
1.BODY&BONNETASTM A 105/F11/F22/LF2/F304/F304L/F316/F316L/F51/F53/F55/F347/F321/INCONEL 625/MONEL 400/HASTELLOY C276/ALLOY 20
2.WEDGEASTM A 217 Gr CA15/ASTM A 351 Gr CF8/CF8M/CF3/CF3M
3.stemASTM A 182 Gr F6a/F304/F304L/F316/F316L
4.seat ringASTM A 479 TYPE SS410,SS304,SS316,SS304L,SS316L/FS A 182 F304/F316/F304L/F316L
5.BACK SEATIntegral
6.GLAND BUSHASTM A 479 TYPE SS410,SS304,SS316,SS304L,SS316L/FS A 182 F304/F316/F304L/F316L
7.GasketSS316 Sairal Wound Grafite Filer
8.PACKING100% Grafite
9.Gland flangeA105/CARBON STEEL
10.YOKE NUTA105/CARBON STEEL/GUN METAL
11.HAND WHEELSG IRON/CARBON STEEL
12.HAND WHEEL NUTMS/CARBON STEEL
13.BODY&BONNET JOINT BOLTASTM A 193 Gr B5/B6/B7/B7M/B16/B8/B8A/B8C/B8M/B8MN
14.EYE BOLTA105/A182
15.EYE BOLT NUTASTM A 194 Gr 2H/8/8M
16.CROSS BOLTASTM A 193 Gr B7/B7M/B8/B8M
17.CROSS BOLT NUTASTM A 194 Gr 2H/8/8M
18.YOKE SLEEVESG IRON/D2/GUN METAL